You can increase the WiFi signal range of the router with the aid of the Linksys RE6500 extender. The two frequency bands of 2.4GHz and 5GHz make up the Linksys RE6500 extender. A dual-frequency band will enable you to access the internet quickly everywhere. For login and setup instructions for the RE6500 extender, read the bottom instructions.

Linksys RE6500 Extender Advantages

Increase the existing router's WiFi signal range as soon as possible. 

Connect to any kind of installed router. 

The Linksys RE6500 extender's WiFi-protected setup button facilitates router connection. 

Perform the login and setup procedures quickly. 

Despite being little, it serves multiple purposes.

Login To The Linksys RE6500 Extender

Find the RE6500 extender power plug in the wall or power outlet first. 

Grab a WiFi device, like a laptop or computer, then join the Linksys extender network after that. 

Open the navigation afterward and enter extender.linksys.com in the address field. 

The Linksys extender login page has just appeared on your computer screen. 

Enter the extender's default login information.

Observe the on-screen display directions. 

To finish logging into your Linksys RE6500 extender, tap the login button.

Resolve The Linksys Extender Login Error

Ensure that the repeater and computer are connected. 

Check the Linksys RE6500 WiFi range extender's LED status. 

Try turning the Linksys RE6500 extender on and off. 

Must use the Linksys RE6500 extender's default web address.

Connect Your Devices By WPS Method

Your router needs to support the WPS button in order to start using this method. Try a different technique to pair the extender with the router if the router does not support a particular WPS button.

Make sure the router is first positioned closer to the extender. 

Press the Linksys RE6500 extender's WPS button now. 

Press the WPS button on the router that is already there after 20 seconds. 

Afterward, the WPS LED begins to blink continuously, showing that the Linksys RE6500 setup is successfully complete. 

Locate an extender in the area where you want to make use of the fast internet speed. 

Setup Linksys Extender By AP Mode

Consider this AP mode to complete the Linksys WiFi extender setup if the WPS method of connecting the extender to the router doesn't work.

Install the Linksys extender power plug first into the outlet. 

Now, connect the Linksys RE6500 extender via an Ethernet wire to the main router's LAN port. 

Next, connect a WiFi device to the network of the Linksys WiFi range extender. 

Launch the browser later on a WiFi-connected device, and then type the default web address into the address box. 

For the access point mode, also generate a network name and password. 

Finally, take into account all the display instructions.

If you experience a problem after setting up your Linksys WiFi extender, take into account the following advice.

Troubleshoot The Problem Of  Linksys Extender

There are numerous ways to solve problems with the Linksys RE6500 extender. Think over each suggestion for a solution individually.

Position Of The Linksys Gadgets

A vital consideration is where the extender and router are placed. Metal appliances take all WiFi signals from the repeater and router devices, therefore if your extender is positioned next to metal or electronic devices, move the router right away. The optimal placement for your home and workplace is in the center.

Remove Unnecessary Gadgets

It is advised that you turn off any unused WiFi devices. If you are unsure of the number of WiFi devices that are linked to the extender network, go to the Linksys extender configuration page and look for the WiFi devices connected option. Remove any devices that are not in use.

Improve the Speed Of Linksys Extender

You can experience problems as a result of the extender's outdated software. We advise you to immediately update the Linksys extender's software as needed to resolve the problem. To upgrade the program, think about the following actions.

You can improve performance by going to the Linksys extender web control page. After that, choose a software upgrade and then search for administration. Now, if any new software file is available, download that. You must restart your extender in order to complete further installation. 

Do Reset Linksys WiFI Extender

You can find the reset hole button on the RE6500 extender's back. With a paperclip, press the button for 10 seconds. As of right now, none of the repeater LEDs are on. The Linksys RE6500 extender is now reset after performing this

Note: Repeat the Linksys RE6500 setup procedure after clearing the Linksys extender settings.

After reading this page in its entirety, you will be able to login and configure the Linksys RE6500 extender. If you have a Linksys Velop device and are having trouble configuring it, go to the Linksys Velop setup webpage and take all of the display instructions into consideration.

Author's Bio: 

Hi I am Henry who provides blogs related to business, technology.